Loading

Wood Preservation & Damp Proof Systems

terrace image

Timber Repair Systems

house image

Triton's range of epoxy products are principally designed for structural and non-structural repair of timber and masonry. Within this range are structural grouts for repairing voids or bearing ends in timber affected by insect attack or rot, non structural mortars for filling voids in timber or masonry, adhesives for bonding structural fixings, consolidants for insect damaged and friable timber and waterproof coatings for walls and floors, above and below ground.

Downloads:

Triton Timber Manual
Download (4.3Mb)

 

Trimol 15 Lightweight Mortar

Ideal for fast repair of concrete in vertical and overhead work and rapidly attains mechanical strength sufficient to exceed that of good quality concrete. A 3-component system which provides a cold or warm setting, lightweight, low slump filler for use in non-structural applications. Best used in conjunction with Trimol 23 as a primer.

Supplied in 5 kg packs.

Downloads:

NBS Plus Product Entry
Download (78Kb)

Trimol 15 Data Sheet
Download (106Kb)

Trimol 15 Material Safety Data Sheet
Download (365Kb)

Top of page

Trimol 23 Thixotropic Epoxy Adhesive

Professional Products - Wood Preservation & Damp Proof Systems picture
Shakes stitched with steel dowels set in Trimol 23

Designed for building and civil engineering applications where a thixotropic (negligible slump) adhesive or primer is required. A 2-component solvent-free adhesive, Trimol 23 can be applied in cold, damp conditions and will remain in place on vertical or inverted surfaces. Forms a strong bond to wood, metals, glass reinforced plastics and laminates.

Supplied in 0.66 litre packs.

Downloads:

NBS Plus Product Entry
Download (78Kb)

Trimol 23 Data Sheet
Download (102Kb)

Trimol 23 Material Safety Data Sheet
Download (147Kb)

Top of page

Trimol 34 Timber Consolidant

A two component low viscosity epoxy resin system which creates an almost colourless liquid to provide a cold or warm setting consolidant for wood. Will consolidate friable, worm infested or tack-damaged furniture and provide a base upon which to carry out further restoration.

Supplied in 1.34 litre packs.

Downloads:

Trimol 34 Data Sheet
Download (94Kb)

Trimol 34 Material Safety Data Sheet
Download (240Kb)

Top of page

Trimol 36 Structural Grout

Professional Products - Wood Preservation & Damp Proof Systems picture
Strengthening beam with Trimol 36
Case Study button

A three component, pourable epoxy resin system for use as a structural grout. Cold or warm setting, Trimol 36 gives a structurally discreet back-fill, principally for timber repairs. The cured product creeps sufficiently under loading to accommodate movement in complex timber joints. A versatile product for site repairs to rotten, insect or fire damaged timbers and to remake joints or breaks. Recommended for use with Trimol 50 reinforcement rods.

Supplied in 2.69 or 8.13 litre packs.

Downloads:

Trimol 36 Data Sheet
Download (119Kb)

Trimol 36 Material Safety Data Sheet
Download (369Kb)

Product Fire Rating Data Sheet
Download (1.5Mb)

Top of page

Trimol 40 Water Based Epoxy Coating

A two component water based expoxy coating for floors and walls. Trimol 40 is typically used to provide a damp proof membrane on walls and floors either on its own as a wearing surface or in a "sandwich" construction between sand and cement renders. Can be applied to brick, concrete, stone and cement renders when damp.

Supplied in 1, 2.5 and 5 kg packs.

Downloads:

NBS Plus Product Entry
Download (78Kb)

Trimol 40 Data Sheet
Download (102Kb)

Trimol 40 Material Safety Data Sheet
Download (242Kb)

Top of page

Trimol 50 Reinforcement Rods

Professional Products - Wood Preservation & Damp Proof Systems picture

Professional Products - Wood Preservation & Damp Proof Systems picture

Manufactured from glass reinforced resin by "pultrusion". Trimol 50 rods have outstanding tensile strength compared to steel, are flexible and compatible with Trimol 36 structural grout.

Supplied in a range of sizes from 3 - 25mm diameter.

Downloads:

Trimol 50 Data Sheet
Download (106Kb)

Top of page

Trifix Adhesive

A two-component epoxy resin system (for use in "side by side" cartridges) formulated as an anchoring adhesive to give a strong, stress free joint within brick, stone, mortar or timber structures. A solvent free thixotropic product which cures in cold, damp conditions.

Supplied in 400ml cartridges.

Downloads:

Trifix Adhesive Data Sheet
Download (102Kb)

Trifix Adhesive Material Safety Data Sheet
Download (254Kb)

Top of page

Triseal

Damp proof membrane and water vapour suppressant

Wood Preservation & Damp Proofing - Epoxy Systems picture

Wood Preservation & Damp Proofing - Epoxy Systems picture

A solvent free, two part epoxy resin coating, typically used as a surface damp proof membrane and a water vapour suppressant. Well suited for use as a water and water proof barrier, beneath raised access floors, in plant rooms and bunded areas. It is also suitable for application on damp surfaces, such as sand/cement and cement floors subject to rising damp or containing residual construction moisture. Tri-Seal can be used as a general purpose coating for surfaces subject to foot and light wheeled traffic. Tri-Seal can be applied using a brush or medium pile roller onto sound, clean surfaces. NB New concrete subfloors or sand/cement screeds should be left for a minimum of seven days to cure before applying this product.

Triseal is available in 2.5 litre, 5 litre and 20 litre packs.

Downloads:

Triseal Data Sheet
Download (2.2Mb)

Triseal Material Safety Data Sheet
Download (262Kb)

Top of page